GSM独立门磁/振动报警器
使用说明书
四频
本产品由军工品质的GMS模块组成，具有声音监控的功能及振动感应报警等功能,并且具有远程GSM免费基站定位功能，安装在家居、公司及厂房或汽车，当仓库有声音，门窗被打开时，它便会立即通知你马上查看，确保家人生命及财产安全。本产品体积小巧，语音清晰，待机时间长，操作简单，性能稳定，无需安装，无需布线，即买即用，可远程控制等特点，应用广泛。
产品示意图:
主机及磁条分别贴在门及门框上即可.
使用方法：
开机：将SIM卡按指示的方向插入卡座，蓝色指示灯快闪1次，表示电源已经接通，约30秒后指示闪三次表示已经搜网成功.
选择产品语言
发送LAG1将提示语言更改为中文。(出厂默认)
发送LAG2将提示语言更改为英文。
发送LAG3将提示语言更改为俄罗斯语。
功能设置
发送GDM1启动声音监控，当现场有声音即拔打您的电话。
发送GDM2取消声音防盗。
发送GDM5启动门窗磁控感应监控，当门窗被打开/关上时即发短信给您并拔打您的电话。
发送GDM6取消门窗磁控感应监控。
发送TIM** 更改声音监控拔号间隔。
发送LBS查询本机当前基站编号及地址地图链接.
发送MOD1报警方式改为先发短信再拔打电话.(出厂默认)
发送MOD2设置报警方式为仅拔打电话。
发送MOD3报警方式为仅发送短信。
发送DSP查询设备状态.
如需要启动自动应答功能,请先发送短信HM1(2,3,4,5) 绑定自动应答号码.否则不能自动应答.注:最多可以绑定5个号码.
注意事项：
*本机默认插入SIM直接开机。
*充电时请将SIM卡插上.
*新机使用前需充电3-4小时，以达到最佳的效果，充电时请使用本机配送的充电器，以免损坏主机。
*待机时间：160-240小时.视当地网络信号强弱而定。
*不自动应答：
确认是否为GSM卡，本机使用的是GSM网络。确认是否绑定自动应答号码.
为了确保安全和保密性请务必使用新卡。
网络：（二选一）
GSM850/900MHz/DCS1800/1900MHz
配件：
主机一台
磁盒一个
充电器一个
USB充电线一条
GSM independent Multi-function alarm
User Manual
Quad-band
This product use military technology GSM module withmulti sensor components, also have remote sound pickup function, can be installed in home, companies,shops and warehouse, this product compact size, voice clear, long standby time, simple operation, stable performance, without install, remote control etc.,
Product view:
Usage:
Pleaseopen the back cover and you can see SIM card holder. insertSIMcardwithright direction as instruction,thelights flash 1 time, means the TC-100 has been switched on, the light will flash 3 times about after 30 seconds,that's means ready for work.
Past the host and magnet box on door and door case.
Switch language
SendLAG1change the language to Chinese.
SendLAG2change the language to English.
SendLAG3change the language to Russian.
FunctionSettings:
SendGDM1 start voicesensor alarm,when sound around ,TC-100will call the sender.
SendGDM2 stop voice control.
SendGDM4startmagnetic sensoralarm,whenthe door was opened or closed ,the product willsent SMS or call the sender.
SendGDM5 stopmagneticsensor control.
SendTIM**set voice control call back interval.
SendLBSreport GSM base station ID and location map link.
sendMOD1the alarm mode will change assend SMS first, and then call.
sendMOD2the alarm mode will change asonly call.
SendMOD3the alarm mode will change as Send SMS only.
SendDSPcan inquire the current state
If you want TC-100 answer incoming call automatically, please binding number:send SMSHM1 (2,3,4,5),setting the SMS sender as emergency number.when the sender call TC-100, it will auto-answer this call.The emergency number can be up to 5 .
Note:
Boot this machinemust beinserted SIMcard.
Pleaseinserted the SIM cardwhen charge.
The new machines need to be recharged 2-3 hours before first use. Please use our distribute charger to protecthost.
Standby time:160-240hours.depending on the local network signal strength may be.
if the product can’t Auto-Answer:please confirm whetherbanding emergency number.
Network type:
GSM850/900MHz/DCS1800/1900MHz
Accessories:
Host 1
Magnet bos 1
Charger 1
USB Charging Cable 1