DESIGNATION品名：DC socket | MODEL型号：DC-022B | EDITION版本：01 | PAGE页码：1 OF 2 |
1.0构造Tectonic |
A型状、尺寸依照制品图而规定.
Shape, size in accordance with the provisions of map products. |
B外观:各部位应良好无秤锈、裂痕、电镀不良现象. Appearance : the good parts should weigh no rust, cracks, electroplating ill. |
2.0使用环境条件The use of environmental conditions |
A环境湿度Humidity:25℃~+70℃ |
B相对湿度Relative humidity:≤93% (+40℃) |
C机械性能Mechanical properties |
D动作力Power moves:3~25N |
E端子强度Terminal Strength 各端子在各方面承受500克力作用下,在10秒内,无脱落、破损等不良现象,但弯曲也可. The terminals in all aspects under 500Caledon role, in 10 seconds, without any loss, damage and other negative phenomena, but also bending. |
4.0电气性能Electrical Performance |
A额定电流Current ratings:DC 12V1A . |
B接触电阻Contact resistance:50mΩ以下. |
C绝缘电阻Insulation Resistance: 在端子之间各端子与壳之间加AC 500V条件下,持续1分钟测试.100mΩ以上.The terminal between the terminal and Shell in between 500V AC conditions, sustained a minute test Ω m above .100. |
D抵抗电压Resistance voltage: 在端子之间端子与壳之间加AC 500V 60Hz条件下,持续1分钟测量.无击穿现象出现.In between the terminal and the terminal shell in between AC 500V 60Hz conditions, sustained a minute measurement. No breakdown phenomenon. |
5.0可靠性试验Reliability Test |
A寿命试验Life Test 以涂有薄层润滑脂的插头(涂润滑脂防止摩擦过热)以每分钟15~20次,无负载插座拨出5,000次，符合规格3.0和4.0规定值.Coated with a thin layer of grease plugs (TU Grease prevent friction overheated) per minute to 15 ~ 20, a no-load socket allocated 5,000, with the specifications 3.0 and 4.0 provides value |
B温度试验Temperature Test 将插座放置于40±2℃,相对温度90%~95%环境中,96个小时后取出,取去水滴,将插座放置于常温常湿环境中,于30分钟内测试,符合规格3.0和4.0要求.Socket to be placed on the 40 ±2℃, relative humidity of 90% ~ 95% of the environment, 96 hours after the removal, taking a drop of water, will be placed in the socket temperature often wet environment, in the test within 30 minutes, with 3.0 and 4.0 specifications required. |
|
|
|
C耐热试验Heat test 将插座放置于70±2℃环境下,96个小时后取出,将插座放置于常温常湿环境中,于30分钟内测定,符合规格3.0和4.0要求.Socket to be placed on the 70 ±2℃environment, 96 hours after the removal of sockets placed on the temperature and moisture environment, within 30 minutes measured with 3.0 and 4.0 specifications required. |
D耐寒试验Hardy trial |
将插座放置于-40±3℃环境中,96个小时后取出,取去水滴,将插座放置于常温湿环境中.于30分钟内测定,符合规格3.0和4.0要求. Socket to be placed on the 40 ±3℃environment, 96 hours after the removal, taking a drop of water, will be placed in the socket regular temperature and humidity environment. Within 30 minutes measured with 3.0 and 4.0 specifications required. |
5.5耐焊接热试验Thermal resistance welding test 插座耐焊接热试验中,符合规格3.0和平共处4.0要求. Socket welding thermal resistance test, with the specifications required 4.0 3.0 peaceful coexistence. |
A自动焊;温度235±5℃,时间5±1秒.Automatic Welding; Temperature of235℃± 5, ± a time five seconds. |
B人动焊;温度350±10℃,时间3±0.5秒.People to welding; The temperature of 350 ±10℃for 3 ± 0.5 seconds. |